 |
 |
 |
|
1988 - 1992 Camaro Body Side Trim Molding Set with Pointed Ends
Closeout! These items are discontinued by the supplier. Limited stock available – once they're gone, they're gone!
New RED 1988 - 1992 Camaro exterior body side trim molding set. Exact fit for all 88 - 92 models. This new set comes complete with 2 Eight Feet long rolls, not cut so you can trim to fit your particular car. Proper Molded ends and they come to a point like originals. Measures just under 1 inch wide at 7 / 8". Installs in minutes!
*This kit comes in (2) 8ft. strips so you will need to cut it at the door on the front were it meets the fenders and also the rear quarters. Manufactured with original equipment approved polymers, Mylar laminates and 3M acrylic foam tape on the back side for a quick easy installation! Outstanding performance and reliability.
Complete set to do both sides! Order your new Body Side Molding Kit today!!
PART NUMBER: BCM-96K
- Application Procedures for Pressure-Sensitive Body Side Moldings
Outlined below are the recommended procedures for applying pressure-sensitive Body Side Moldings (BSM). These procedures address the key points for a successful BSM application.
The body of the vehicle must be clean and dry to achieve the best adhesion. The pressure-sensitive adhesive on the molding must not be contaminated during the application. The molding must be applied to achieve complete contact (bond) of the adhesive to the vehicle. (i.e. maximum wet-out).
Installation Area:
The installation area should be kept reasonably clean. Any airborne dust, oils, etc. may contaminate the vehicle or BSM adhesive and reduce the bond of the tape.
Vehicle Surface Preparation:
The vehicle surface should be washed with an appropriate solvent, one commonly used system is a 70% mixture of Isopropyl Alcohol and water (Rubbing Alcohol). To assure removal of all contaminants it may be necessary to first wipe with TG Prep, then use the 70% Isopropyl Alcohol mixture. * Use clean lint free wiping cloths or disposable wipes such as Kim wipes. * Reprocessed rags should not be used as they may contain wax or residue.
Step 1
After washing, the vehicle surface should be thoroughly dried. Again use a clean, dry, lint free cloth. Vehicle surface application temperatures of 80'F (26'C) to 110'F (44'C) are recommended for best tape adhesion. The warmer surface will help wet-out the adhesive on the tape. During cold weather applications the vehicle surface can be heated with a heat gun or heat lamps, but do not heat the surface of the molding. Application of the BSM at temperatures below 64'F (17'C) or above 110'F (44'C) must be avoided.
Step 2
Body Side Molding Preparation:
The BSM should be stored at room temperature in a clean dry area. Cold temperatures require heating to warm the molding to the proper application temperature (i.e. Floor heater of vehicle). There is no damage to the tape or molding stored at colder temperatures, but moisture and condensation must be avoided. The molding can be heated up to 100'F (38'C) for application. This will soften the molding, making it easier to conform to the vehicle contours, as well as improve adhesive wet-out. The liner on the adhesive should not be removed until application to the vehicle. This will help prevent contamination of the adhesive surface.
Body Side Molding Application:
Align the molding with a key feature such as the front and rear bumpers or with a body line to ensure proper molding alignment. Placing ½" masking tape along the desired installation area is an excellent guide for applying the molding straight.
Step 3
Measure 3 times before cutting to fit your particular car. Be certain to leave enough room for the door to open properly after the molding has been installed. (Bevel cut if necessary).
Step 4
Remove the liner from the tape as you are applying the molding to the vehicle. Be careful not to contaminate the adhesive. Common sources of contamination are: oil from the applicator hands, dust or lint from clothing, work tables, or the floor. Do not touch the adhesive at any time. Contaminated moldings should not be used
Step 5
Apply the moldings with a rolling motion to prevent entrapment of air between the tape and the vehicle surface. Use firm hand pressure to ensure good adhesion of the molding.
Step 6
A roll down with a hard rubber hand roller is recommended to assure complete wet-out of the adhesive to the vehicle surface. Apply firm pressure while rolling the molding to properly wet-out the adhesive.
Step 7
Check the edges of the molding to assure good tape adhesion. Re-roll with more pressure as necessary to achieve a good bond.
Step 8
Enjoy the fresh clean look of your new body side trim!
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Red
- 7 / 8" Wide with Pointed Ends
- 3M Acrylic Foam Tape Pre-Installed
|
|
|
|
|
|
| Other Great Parts That You Might Need |
|
1982 - 1992 Camaro Door Jamb Sill Plates, Choose Color
|
|
1970 - 1992 Camaro OE Style 18" Windshield Wiper Blade, Black, Each
|
|
1982 - 1992 Camaro Dash Pad, OE Factory Style
|
|
1982 - 1992 Camaro Interior Rear Hatch Cargo Panel Trim Screw, Plastic, Colors, Each
|
|
|
|
|
|
|
|
|
|
|
|
|
1986 - 1992 Camaro Header Panel Emblem, Bow Tie Shield, IROC-Z and 87 Rally Sport
|
|
1982 - 1992 Camaro Upper Door Hinge 12392848, LH or RH, Each
|
|
1982 - 1992 Camaro Outer Window Felts Pair
|
|
1991 - 1992 Camaro Bumper Cover, Rear, Urethane, OE Style
|
|
|
|
|
|
|
|
|
|
|
|
|
1985 - 1992 Camaro Front Lower Air Deflector, Center Spoiler
|
|
1985 - 1992 Camaro Front Bumper Cover, OE Style Urethane Rubber
|
|
|
|
|
|
|
|
|
|
|
|
|
body side molding 
