 |
 |
 |
|
Holley Sniper 2 Electronic Fuel Injection Kit (4150 flange) w/ PDM, SBC or BBC, Black
Take your Camaro to new heights with the #1 EFI conversion system! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley has added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more.
New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that's required from your vehicle to power the PDM and your Sniper EFI. 
Make your classic drive like a modern fuel-injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.
If you're looking for a high-performance Camaro fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Fitment includes all 67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, and 81 Camaro equipped with SBC or BBC.
NOTE: External Regulator required for this installation.
PART NUMBER: FUE-1102
- Main Features
- All new design – the #1 EFI Conversion just got better!
- Only four wiring connections required: Battery+, Battery-, Switched Ignition, and RPM
- Calibration wizard only requires that you answer a few simple questions about your engine to create a base map and begin self-tuning – No laptop required
- Supports up to 650hp naturally aspirated or 575hp on boost with four 100 lb/hr injectors
- (NEW) Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires)
- (NEW) Redesigned throttle shaft and plate geometry for a smoother throttle feel
- Sniper 2 is Part of the Sniper EFI Complete Ecosystem
- Sniper 2 is compatible with the complete Sniper EFI Ecosystem that includes plug-n-play Hyperspark Ignition systems (coil, ignition box and distributor), fuel systems (fuel lines, fuel pump hangers), multiple displays and more
- (NEW) Main harness includes plug-and-play HyperSpark distributor support, for integrated timing control, making your ignition setup hassle free
- (NEW) Adaptors for other ignition types sold separately
- (NEW) Wide Variety of tuning and gauge display interfaces: from a 3.5-inch full color LCD Handheld, 5-inch Digital Dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2
- (NEW) Integrated transmission kick down provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications
- (NEW) “Hidden Harness” wiring harnesses exits from the rear of throttle body for a clean appearance
- (NEW) Inputs and outputs consist of: 2x Ground Inputs, 2x Ground Outputs, 1x TPS output (0-5v), and 1x Tach Output
- (NEW) Redesigned injector connector for improved reliability
- (NEW) Onboard contactless magnetic TPS sensor ensures an accurate TPS reading
- (NEW) Next Generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection
- (NEW) Cast-in fuel crossover from the primary to secondary fuel rail
- (NEW) Sniper 2 throttle bodies are serialized, which provides each unit a birth certificate for an improved customer service and warranty experience in the event of any unit needing to be inspected
- The included genuine Bosch LSU 4.9 wideband oxygen Sensor provides real-time fuel map learning
- Included clamp-on oxygen sensor kit ensures a leak free oxygen sensor installation with stainless steel T-Bolt clamps and a stainless steel weldable oxygen sensor flange
|
|
|
 |
|
 |
| Other Great Parts That You Might Need |
|
1970 - 1973 Camaro Sniper EFI Notched Fuel Tank System Kit, 255 LPH
|
|
1967 - 1981 Camaro Holley Sniper 2 Transmission Control kit, (92-97 Ford AODE/4R70W)
|
|
1967 - 1981 Camaro Sniper EFI HyperSpark 2 Ignition System for Chevy SBC / BBC, Black
|
|
1967 -1981 Camaro Holley Sniper EFI Billet Fuel Regulator, 6AN
|
|
|
|
|
|
|
|
|
|
|
|
|
1967 -1981 Camaro Holley Sniper EFI Billet Fuel Regulator, 8AN
|
|
1967 - 1981 Camaro Sniper EFI HyperSpark 2 Ignition System for Chevy SBC / BBC, Polished
|
|
Earl's Vapor Guard Hose Ends with 3/8 Vapor Guard Barb to -6 Female w/ 1/8 NPT Gage Port
|
|
Holley EFI Fuel System Kit
|
|
|
|
|
|
|
|
|
|
|
|
|
Holley Sniper 2 Electronic Fuel Injection Kit (4150 flange), SBC or BBC, Black
|
|
1967 - 1981 Camaro Holley Sniper 2 Transmission Control kit, (2009+ 4L60E)
|
|
1969 Camaro Sniper EFI Fuel Tank System Kit, 255 LPH
|
|
1978 - 1981 Camaro Sniper EFI Fuel Tank System Kit, 255 LPH
|
|
|
|
|
|
|
|
|
|
|
|
|